AI Assistant
Notifications
Clear all
Norman_Oklahoma
Norman_Oklahoma
@norman-oklahoma
Member P&R, Founder
Joined: June 15, 2015 7:55 am
Last seen: October 13, 2026 9:23 am
Topics: 200 / Replies: 8297
Reply
RE: Leveling Pin

A large screwdriver would serve the purpose very well.

1 year ago
Reply
RE: ALTA showing proposed billboard

Bingo. Your ALTA would show a billboard in in the "wrong" location. Too many people just are not going to clue into your "proposed" location notes.

1 year ago
Reply
RE: ALTA showing proposed billboard

THe TRs I've seen lately usually do have the vesting deed linked, but the title company description is not always a copy of the vesting deed descripti...

1 year ago
Reply
RE: ALTA showing proposed billboard

I heard a story once of a legal description with a scriveners error - a bearing that was shown NW when it should have been NE. When interpreted as NE ...

1 year ago
Reply
RE: 100 year flood

First off..... it's really difficult to decipher your all caps stream of consciousness. I gather that you are proposing to stake the flood line tha...

1 year ago
Reply
RE: Calculator for FS exam

I did my FS in 1997 with a HP48Gx and SMI card. Which was "legal" at the time. But out of 165 questions there were about 5 that I really used the COGO...

1 year ago
Reply
RE: Evidence and Procedures for Boundary Location Seventh Edition

I always recommend that the student should start with a 1st, 2nd or 3rd edition before taking the plunge on the very latest edition. These early editi...

1 year ago
Reply
RE: Issue: Leica CS20 keeps showing points from previous jobs in the 3D view.

The CS20 uses your current job as a template for the next job created. That is why the settings gets carried over.

1 year ago
Reply
RE: Issue: Leica CS20 keeps showing points from previous jobs in the 3D view.

I suspect that you have an old job "linked" to your new job. Check under the "Linked Jobs" tab of "View & Edit Job Properties"

1 year ago
Reply
RE: "Substitute" PK Nails

The city and county surveyors here in Oregon require the setting of centerline monuments in new subdivisions, and these must be 5/8" rods with aluminu...

1 year ago
Reply
RE: Unwritten rule against this?

#5 rebar is required for property corners in Oregon (pipe may also be used, but almost nobody does that), and has been for a long time. Plenty of tim...

1 year ago
Reply
RE: Unwritten rule against this?

I go one step further and say just don't set control near a property corner, period. It sometimes takes some doing but it can usually be done. If it ...

1 year ago
Reply
RE: Notes from the Virgin Islands

I predict that the board will issue a reprimand and $250 fine. But that's OK, because the board action will result in the engineers E&O insurance...

1 year ago
Reply
RE: Thinking of leaving CA…

I bought my house for $139,500 in 1995. I was a PC/Office tech at the time. That equates to about $292,000 of todays dollars. Houses in the neighborho...

1 year ago
Reply
RE: What's with OPUS?

Several weeks ago we had a thread about the rather large number of NGS employees accepting the reduction in force opportunity, plus many outright reti...

1 year ago
Reply
RE: Seeking RPLS to Review & Certify Completed Form Board Survey – Royse City, TX

I did these in British Columbia at the beginning of my career. We might do 5 in a day. I think that it makes a lot of sense to survey and certify the...

1 year ago
Reply
RE: Building Setbacks on a ROS

Chuck Pearson was never shy about accumulating and using what ever power he could get. Bob Hovden seemed to be in perpetual pursuit of, while never qu...

1 year ago
Reply
RE: Railroad Survey Advice

That's going to fall in the ballast at the center of the track, more often than not between ties. What a colossal PITA to set rods that has to be. And...

1 year ago
Page 31 / 425