I sure hope, that t...
 
Notifications
Clear all

I sure hope, that there aren't high expectations

20 Posts
17 Users
0 Reactions
0 Views
(@doug-crawford)
Posts: 681
Topic starter
 

Media photo of an fatal aircraft crash. They did get the 'gun' above the corn.

 
Posted : 17/09/2016 8:23 am
(@mark-mayer)
Posts: 3363
Registered
 

Doh!

 
Posted : 17/09/2016 9:21 am
(@shelby-h-griggs-pls)
Posts: 908
Registered
 

They forgot to bring one of these: http://certainty3d.com/products/topolift/

 
Posted : 17/09/2016 9:28 am
(@eddycreek)
Posts: 1033
Customer
 

Should be fine. The big guy is holding the tailgate down so the bed don't bounce.

 
Posted : 17/09/2016 12:31 pm
(@jerry-attrick)
Posts: 326
Customer
 

That looks like a big "girl" to me.

JA. PLS SoCal

 
Posted : 17/09/2016 1:24 pm
(@monte)
Posts: 857
Registered
 

And I thought I was joking when I suggested putting the gun in a utility bucket and lifting it above the reeds on a pond once.... (yes, frustration was abundant!)

 
Posted : 17/09/2016 1:40 pm
(@holy-cow)
Posts: 25292
 

All they really needed was three more stepladders............one for each leg of the tripod to set on. That at least has a chance of working. Being in the bed of a pickup absolutely will not work.

 
Posted : 17/09/2016 2:05 pm
 rfc
(@rfc)
Posts: 1901
Registered
 

Actually, the setup is fine, and it IS about expectations. To document aircraft debris, +/- a foot or so would probably be more than enough accuracy. Add to that the fact that rocking the truck on its suspension would have a much greater effect on the verticals, and very little on the horizontals, which is what they're mainly interested in.

 
Posted : 17/09/2016 3:44 pm
(@peter-hughes-davies)
Posts: 218
 

Many moons ago (1969 ish) we once improvised a really really high setup to see over a highway noise barrier by setting three tripods without tribrachs and then the top tripod on top of them. It was for control and we measured many sets of angles . . got the job done.

 
Posted : 17/09/2016 3:48 pm
(@holy-cow)
Posts: 25292
 

Try to level that rascal. It's impossible.

 
Posted : 17/09/2016 5:03 pm
(@dave-karoly)
Posts: 12001
 

Picture it, need to scan a Dozer sitting on a lowboy trailer (seized engine so can't move off the trailer). The mechanic brought the forklift over and secured a pallet to it. Then we tied down the Trimax to the pallet and put the scanner on it. Ran it up to height. They had a moving staircase which I used to walked up to level the scanner. Operation was done with our iPad. It was a little shaky but it worked.

The twist is the mechanic has an LSIT. He was very interested, of course. The State pays the lowest paid Surveyor more than the best paid mechanic so he is working on getting a job at Caltrans.

 
Posted : 17/09/2016 5:21 pm
(@sjc1989)
Posts: 514
Registered
 

Used to have three U-channel steel fence posts to extend my legs. It worked as well as anything I have ever used, much better than that pick up bed.

Steve

 
Posted : 17/09/2016 6:34 pm
(@ron-lang)
Posts: 320
Registered
 

I've once setup on a shingled a frame garage to get above the corn, but never the bed of a truck. The reason was because the farmer didn't take it to well that on the previous day we cut a 3' wide 2000' line through the middle of the corn field.
We did ask the office before cutting the line they said do what you gotta do. Story changed after farmer ripped them a new one.

 
Posted : 18/09/2016 6:12 pm
(@lee-d)
Posts: 2382
Registered
 

If you ever ran seismic lines through the swamp then you probably know what a "treebrach" is... sometimes you disable the compensators and do what you have to do to get the job done. And RFC is right; for the accuracy they need that setup is fine, you don't always need mm accuracy, especially for mapping.

 
Posted : 19/09/2016 4:59 am
(@steve-gilbert)
Posts: 678
 

Actually it's a good idea. In the future, they will always have a control point wherever that truck is!

 
Posted : 19/09/2016 5:46 am
(@andy-bruner)
Posts: 2753
Registered
 

Doug Crawford, post: 391512, member: 9 wrote: Media photo of an fatal aircraft crash. They did get the 'gun' above the corn.

You laugh but I did see an Instrument Man set up a level in the bed of a pickup one time. Needless to say the Crew Chief nearly lost it when he saw what was happening.
Andy

 
Posted : 19/09/2016 7:39 am
(@mike-falk)
Posts: 303
Registered
 

http://www.moogs3.com/literature/MoogS3/Specsheets/SpS/Branch_of_Tripods_Samson_Hercules_Gibraltar_SpS.pdf page 2 of 8

Check model #4-53031-7BQ Maximum height 175"

 
Posted : 19/09/2016 1:11 pm
(@c-billingsley)
Posts: 819
Registered
 

Mike Falk, post: 391710, member: 442 wrote: http://www.moogs3.com/literature/MoogS3/Specsheets/SpS/Branch_of_Tripods_Samson_Hercules_Gibraltar_SpS.pdf page 2 of 8

Check model #4-53031-7BQ Maximum height 175"

Something like that would be helpful, but from what I've seen, police accident surveyors work on such tight budgets that they couldn't swing it. The last one I spoke with had a total station, tripod, and prism pole in the trunk of his cruiser because the department wouldn't put him in a truck. He asked to take pictures of my box because he was going to use them to help convince his superiors that he needed a truck or suv.

 
Posted : 20/09/2016 7:32 pm
(@mark-mayer)
Posts: 3363
Registered
 

Kent may object, but it seems to me that this is a job for RTK.

 
Posted : 20/09/2016 7:41 pm
(@holy-cow)
Posts: 25292
 

Saw a pickup on the road today that reminded me of the photo above. In the back was a mail box mounted on a 4 x 4 post stuck in an old milk can, which is a fairly common sight in front of rural houses. The flag was up, indicating there was mail inside so the mail carrier needed to stop to get it. That would be a good trick at 55 mph going down the highway.

 
Posted : 20/09/2016 7:44 pm