Activity
 
Notifications
Clear all
Peter Kozub
@peter-kozub
Registered
Joined: July 12, 2010 4:46 pm
Topics: 23 / Replies: 221
Reply
RE: Sokkia GSR 2700 ISX radio problem?? Potential Solution

Do you know of anyone in the hood who could set there satel Easy 3Asdto your configuration to see what gives.I set everything on the keypad on the 3AS...

11 years ago
Reply
RE: Sokkia GSR 2700 ISX radio problem?? Potential Solution

Okay I turned of the base at the rover satel uhf 3ASd Easy only theRTSCTS where on and solid red

11 years ago
Reply
RE: Sokkia GSR 2700 ISX radio problem?? Potential Solution

My external UHF Satel radio Easy 3Asd have external indicator LEDs that show at the rover the followingLEDSRTS = ready to send solid redCTS = clear to...

11 years ago
Reply
RE: ROBOT

That sums it up Leica did not have to FIX there Robot like Trampleby using a Active boat sized 360 prism.If Leica required a active prism they would m...

11 years ago
Reply
RE: ROBOT

Yes robots are a necessary evil at timesIn your site and my case I always start with rtk Gps and set control in open areasto close of a open Robot tra...

11 years ago
Reply
RE: ROBOT

This is the order of things in my world Get Excellent RTK GPS set GPS points by RTK use robot due to NO RTK..ROBOT as required then when Sky opens up ...

11 years ago
Reply
RE: Printing charging equipment

Hello Yes LIPO a substantial level of power compared to the old NICD NIMH junk.But most new survey gear the internal Lithium batts are good i.e. my ne...

11 years ago
Reply
RE: Printing charging equipment

Hello NormSome advice on case to contain the LIPO CellsI have spent many endless hours searching Pelican cases and other to no reward to fit the Lipo ...

11 years ago
Reply
RE: Printing charging equipment

Hitech ChargersPlease So Far with the X4 over the last yearAttached is a Lipo I use to power our 1 watt GPS base3 Cell 9000mah Lipo in Polyurethane Di...

11 years ago
Reply
RE: Printing charging equipment

HelloUp here in Canukastan it goes to -20 c no problem for Lipo where as LiFePo are a definite warm temp battery.I have looked at them all Lipo are th...

11 years ago
Reply
RE: Printing charging equipment

Hello NormYes Batterspace.com site could use some work... the singleLipo cells are there they are a BIT of a search to find...way to hard to find to b...

11 years ago
Reply
RE: Printing charging equipment

Lipo Peak voltage per cell 4.2Nominal / average is 3.7so you have 0.5 volts per cell to power your survey gadget this0.5 volts is about 90.0 % of the ...

11 years ago
Reply
RE: Cyber Monday Deal on AutoCAD

I bet most of us on this site would not get out bed for less than $500.00 I have ZERO problem with Autodesk $1000.00 C3D subscription feeannually. Wha...

11 years ago
Reply
RE: Printing charging equipment

I have not had or seen a Lipo fail to fire and I crashed my YAK 45 Carbon Z into the ground bent the Lipo battery in half " no fire or Smoke" and dest...

11 years ago
Reply
RE: Printing charging equipment

I have converted all my equipment to Lipo and charge them with a Hi Tech X 4 charger which has four charging channels this is the fourth model airplan...

11 years ago
Reply
RE: S6 vs S3

I have used them allGeo 650 RobotTrimble 5600 RobotTrimble S6 RentalNew Leica TS12 Robot with power search very niceWhat I have found after 15 plus ye...

11 years ago
Reply
RE: S6 vs S3

Don't buy a trimble you are stuck with there products (service) which should be a open system.I had a Geo 650 aka trimble 5600 with the same bugs what...

11 years ago
Reply
RE: A better way to measure HI?

Don't ............... with RTK GPS but with robot YesOn most day to day jobs I measure Hi over some point talkingrobotMost 99% GPS is the "Here" then ...

11 years ago
Reply
RE: Low end Plotter

Absolutely Not Canon Had a IPF What a piece of Krap Yes HP 111 or newer Had two Hp great One Canon = Junk

11 years ago
Reply
RE: SurvCe and R-8 Model 3

This is why I refuse to buy ANY trimble productsBoycott trimble

11 years ago
Page 8 / 13