Subject: Need Help – Older Firmware for ProMark 3 (Before GPSP010)
Hello everyone,
I have a ProMark 3 that is experiencing issues with position calculation, despite receiving a sufficient number of satellites and having a good PDOP (≈1.5). In the Surveying application, no satellites or signal bars are displayed, and when I try to start recording, the device freezes. However, in Mobile Mapping, the satellite count is displayed correctly, and the position appears to be calculated.
I suspect that the current firmware version (GPSP010) is causing the issue, so I am looking for an older firmware version, such as GPSP009, GPSP008, GPSP007, or GPSP006, along with the associated files (eboot, OSxxx, PM3EUxxx).
If anyone has these files or knows where I can find them, I would greatly appreciate your help. Any advice or suggestions are welcome!
Thank you in advance for your support.
Tabbi Amar
📧 [email protected]
Y
I do not have an answer for your question, but I do have three ProMark 3 units and I am experiencing the exact same situation. Hopefully, someone smarter than I will come along with the fix.
This caught me by surprise as I could see one unit failing, but not all three, at the same time.
Does this firmware update occur automatically when the units were powered on?
UPDATE : I checked the firmware version in my promark 3 and it appears to be P011.
Alan
Dear sir,
I am facing the same problem, if you get any solution, kindly tell me also.
This confirms that other ProMark 3 users are experiencing the exact same issue. The fact that multiple units failed simultaneously strongly suggests that this is not an individual hardware failure but rather a firmware-related issue, possibly due to Week Number Rollover (WNRO) or a software bug.
To answer Alan’s question:
No, the ProMark 3 firmware does not update automatically. An update requires manual intervention using an SD card or PC software like GNSS Solutions.
The next step would be to try installing an older firmware version (P009 or earlier) and see if this resolves the issue. Have you been able to find any older firmware files?
I am reaching out because my ProMark 3 receiver has developed a bug in position calculation, despite receiving a PDOP of 1.5 and a sufficient number of satellites. To attempt a rollback to a stable configuration, I am searching for older firmware versions released before GPSP010.
Could you provide the following files or direct me to a source where I can obtain them?
- Ebootxxx
- OSxxx
- Older GPS firmware (GPSP009, GPSP008, GPSP007, GPSP006, etc.)
- PM3EUxxx software (compatible with the older firmware)
I appreciate any help you can provide in retrieving these files. If you have any recommendations on how to resolve this issue, I would be grateful for your advice.
Looking forward to your response.
Best regards,
No, I haven't found any firmware files. I am currently looking to upgrade my equipment. This isn't the first time I've had problems using legacy equipment and even if we find a fix, it most likely won't be the last. I've been hesitant far to long to upgrade and it's time I put that issue to bed.
The Promark 3 was a valued part of my equipment inventory for quite some time and I look forward to whatever I go with next being as dependable.
Alan
@alan-cook I think it will be the same for me, but I will keep it as a souvenir anyway. thanks 😋 😋
"Advice to all Magellan ProMark 3 GPS owners: Do not update your devices to P010 or P011, otherwise, they will be good for the trash."
"Today, I downgraded the firmware from P011 to P010, but the problem remains the same. The automatically displayed date is July 10, 2005, while today is March 15, 2025, which is exactly 1,024 weeks apart (The GPS week number rollover is a phenomenon that happens every 1,024 weeks, which is about 19.6 years). If anyone can send me P006, I would be very grateful because I have a PR3 that still works with this version."
@tabbi Dear Tabbi ,
I am writing from Greece. I tried to email you, but you didn't answer. Like you , I have 3 Promark 3 and I am trying to find the firmware P009,P008,P007,P006. I have corresponded with Magellan in Holland and Germany , with no results . In fact many other fellow engineers in Greece , we have the same receivers .
One engineer reported to me that all the dealers who sold Promark 3 , have the firmware we asked for , but they don't give it to us and of course advise us to buy new ones .
I have sent an email to China and am waiting for a reply from there as well. I was very pleased with the Promark3 , as I was using them to take 2 initial points and then with the Total Station Nikon , I measure . I will let you know if I receive any news , in relation to the search I am doing .
Best Regards , from Skopelos Greece , Yannis Asteriadis , Civil Engineer .
Dear Yannis,
Please accept my apologies for not replying sooner. Thank you for your message.
Unfortunately, I still haven’t found a solution regarding the Promark 3 firmware (P009, P008, P007, P006). I have received several messages from different countries—many people seem to be facing the same problem. It’s truly frustrating.
As soon as I manage to find a solution or obtain the firmware files, I will make sure to share them with everyone who is looking for them.
Thank you again for reaching out, and best regards from [ALGERIA]!
Sincerely,
Hello! I found P008 firmware but also not working (wrong date). Notice that I have downgraded only the firmware not the FOS212 & Promark3EUV201 because my PM3's are RTK. I don't know how i can send you the files.